{"product_id":"audi-a6-steer-column-lock-j518-elv-module-emulator-with-vvdi-cable-c6-q7","title":"Audi A6 Steer Column Lock J518 ELV Module Emulator with VVDI Cable - C6, Q7","description":"\u003cp\u003eThis product is built to suitable Audi C6 Q7 A6 Steer Column Lock J518 ELV Module Emulator With VVDI Cable.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConnect flashing wire and write the converted EEPROM file. Attention: si-mulator is a 256 chip then choose J518 (2010) (0L01Y) required.\u003c\/li\u003e\n\u003cli\u003eBuy our special burning line, with speakers it is possible to avoid welding burning, directly connect the 20pin port.\u003c\/li\u003e\n\u003cli\u003eIn the platform test, it is necessary to check the wiring of 20Pin port. Some of the platform wiring harness have production problems and are compatible with our burning interface, which may lead to chip damage.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003e\u003cstrong\u003eCompatibility \u0026amp; Programming:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003eApplied To Tepair The AUDI Sixth Gen A6 Q7 Audi C6 Steering Column Lo-ck J518 ELV Module Failure Replacement Emulator\u003c\/p\u003e\u003cp\u003e1. Universal solution, three types MCU all can replaced by this emulator.\u003c\/p\u003e\u003cp\u003e(replace MCU Mask: 1L59W, 3L40K, OL01Y directly);\u003c\/p\u003e\u003cp\u003e2. Stable and durable, No Vulnerable components such as relays, microswitch and motors on it.\u003c\/p\u003e\u003cp\u003eNote: The emulator without lo-ck or on lo-ck function, if need the same function as the original J518 Module, buy the J518 Replacement\u003c\/p\u003e\u003cp\u003eso if you have a car which need replace the J518 module with this emulator, you need read out the data in the MCU by soldering wire or other methods, then write the data into the emulator MCU via this Dedicated cable connector.\u003c\/p\u003e\u003cp\u003eOperating Instructions：\u003c\/p\u003e\u003cp\u003eJ518 256,128 simulate board instruction\u003c\/p\u003e\u003cp\u003eIf your car is 9S12DG 128 CPU, the operation steps are as follows.\u003c\/p\u003e\u003cp\u003e1. Read out the EEPROM data, atttention! Pls save the data, in case of any wrong operation.\u003c\/p\u003e\u003cp\u003e2. Put the EEPROM data into the folder\"EPROM 2K-4K\", then double-click the EEPROM Converter application, and see that the original 2K file becomes 4K, the conversion is successful.\u003c\/p\u003e\u003cp\u003e3. from runing the sytem, the file to be 4K, then the programming succeed\u003c\/p\u003e\u003cp\u003eNote: it is possible to only double click one time, do not repeat. If the double-click run is unsuccessful, or no 4K file appears, then right-key to run the program in administrator mode.\u003c\/p\u003e\u003cp\u003eEach board is with ep data and FLSAH data, so usually you just need to write EP data.If not, it is possible to write the EP data from your car with the FLASH data in the instruction.\u003c\/p\u003e\u003cp\u003eIf car is 9S12DG 256 CPU, the operation steps are as follows.\u003c\/p\u003e\u003cp\u003e1. Read out and save the original car data, and write it directly to the si-mulator.\u003c\/p\u003e\u003cp\u003ewithout horn\u003c\/p\u003e\u003cp\u003eWith horn: wiring according to the silk print in the board,same as board wihtout horn\u003c\/p\u003e\u003cp\u003eAttention: The s-imulator is burned from the test, preferably on the car.\u003c\/p\u003e\u003cp\u003eError wiring: 10 (red) should recover from 20 (blue) or as shown in the figure.\u003c\/p\u003e\u003cp\u003ePackage includes:\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSupported Devices:\u003c\/strong\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e3. Easy for replacing\u003c\/li\u003e\n\u003cli\u003ewrite in the dump form original J518 Module with the VVDI PROG dedicated line directly\u003c\/li\u003e\n\u003cli\u003eNo need solder wire.\u003c\/li\u003e\n\u003cli\u003eThe VVDI PROG dedicated coding cable connector here is only for coding the emulator board\u003c\/li\u003e\n\u003cli\u003enot for original J518 PCB board.\u003c\/li\u003e\n\u003cli\u003eAs for reading and programming the original car\u003c\/li\u003e\n\u003cli\u003epls check the VVDI prog.\u003c\/li\u003e\n\u003cli\u003eVVDI burning line: where: red (thick) =VCC black (thick) =GND yellow =RST purple =BKGD green =XCLKS White =CLK black (fine) =GND-C\u003c\/li\u003e\n\u003cli\u003e1pc x Fit For AUDI C6 Q7 A6 Steer column module J518 ELV Module Emulator with VVDI Dedicated coding cable\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Autokeytechnology","offers":[{"title":"Default Title","offer_id":51796711735606,"sku":"AKT-AUDI-J518","price":120.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0690\/2992\/1078\/files\/J518_7332b35d-c5ea-40ce-8e11-ec7ecab73b07.webp?v=1753481785","url":"https:\/\/autokeytechnology.com\/products\/audi-a6-steer-column-lock-j518-elv-module-emulator-with-vvdi-cable-c6-q7","provider":"Autokeytechnology","version":"1.0","type":"link"}